Nokia 5110 LCD Display interface with Arduino

This LCD device is mainly used in Arduino but it can be connected with any 3.3V controller. These LCDs are used in Nokia 3110/5110 cell phones. It is a very cheap monochrome LCD module made of 84 x 48 pixels. It can be used to display graphics and text together. This display is based on the PCD8544 driver.

Pin configuration of this device is almost like the 16x2 LCD module only instead of 8 data pins one serial data in (Din) pin and one clock (Clk) are there. The list of the pins and their description are listed below.

RST: Pin type active low, so 0V Resets the LCD

CE: Cheap Enable is used to enable the device before sending anything to the LCD

DC: Data/Command is used to select between Rata Register or Command Register

DIN: Data In is used to send information serially to the display. It could be Data or Command

CLK: Clock is used to synchronize the display with the controller

VCC: To power, the pin 5V or 3.3V is applied here

BL: This pin is used to power the Backlight of the display

GND: This is used to ground the device.

Things we need

• Nokia 5110 Display
• Arduino
• Resistors
  1. 1k Ohms x 5 Nos.
  2. 330 Ohms / Potentiometer 1k
• Jumper Wires
• Bread Board

Connection Diagram:

pin 7 - Clock (CLK) pin 6 - Data In (DIN) pin 5 - Data/Command select (D/C) pin 4 - Chip Enable/select (CE/CS) pin 3 - Reset (RST)

Before you upload the code library needs to be installed. Please follow the below mention instruction to install the library.

https://creativestudio1973.blogspot.com/2019/11/introduction-to-arduino-library-manager.html

In the code below we have displayed text, then we have displayed the same text in inverted mode, after that we have rotated the text finally we displayed the ASCII table.
Source Code 1:

Video 1:

Here in the second code, we tested display by displaying an image. To display the image we have to convert the image into code. To do that open the link image2cpp. 
Link: http://javl.github.io/image2cpp/

Go to "Choose Files" and select the file from your computer.

Select the "Canvas Size" to 84x48 and "Scaling" as Scale to fit. Then check the preview to make sure everything is alright.

Now select the "Code Output Format" to "Arduino code" and click on "Generate code"

Finally copy the code and add that to the code below to display an image of your own.

Source Code 2:

Video 2:

Pulse Oximeter MAX30100 Interface with NodeMCU

The MAX30100 has integrated pulse oximetry and heart-rate monitor sensor integrated circuit with I2C interface. NodeMCU is mostly preferred as it is a 3.3V controller.

Components Required:

• Pulse Oximeter MAX30100
• NodeMCU
• Jumper Wires
• Bread Board
• Soldering Kit (Optional)

Before the connection is done there is slight modification needs to be done. The board shown above has little issue with NodeMCU or any other controller. As the NodeMCU is a 3.3V controller it sends or receives I2C signals at a 3.3V logic level. MAX30100 usually comes with its I2C bus pulled up to 1.8V. This is why if you don't make any modifications, the code might not run. Although without modification, you would be able to check its I2C address but rest of the functions won't work.

Now before we go for the modification let's see the Pinout of MAX30100. It has 14 pins. The I2C bus is at Pin 2 and Pin 3 is SCL and SDA. Pin 13 is for INT (Interrupt), Pin 11 and 12 is for Power and Ground.

If we look at the module we will be able to find that Pin 2(SCL), Pin 3(SDA), Pin 5(IR_DRV), Pin 6(R_DRV), Pin 13(INT) are connected to the header. Pin 9(R_LED+) and Pin 10(IR_LED+) are connected to 3.3V. Pin 11(VDD) is connected to 1.8V. Pin12(GND), Pin4(PGND) are connected to the ground. 

Above the red marked 3 pin device is a 1.8V regulator supplying 1.8V to VDD (Pin 11) and also to the three 4.7k Ohms pull-up resistors.

Here we have three 4.7k Ohm resistor pulling up Pin 2(SCL), Pin 3(SDA), Pin 13(INT) up to 1.8V. Here we have to make a change and we have to pull these pins up to 3.3V to connect them with NodeMCU. This could be done in two ways.

Option 1: Remove them and connect 3 external 4.7k Pull up Resistors for 3.3V.

Option 2: Without removing them we will use them by making a slight change in the module. To do that at first with a help of a sharp cutter we will disconnect them from the 1.8V pin of the regulator. Just make a cut at the Red marked position shown in the image below. To make sure the disconnection is complete check continuity using a Multimeter. Do it carefully so that no damage happens at any other part of the device.

Then Connect the points shown below. Make sure during soldering no other points get connected.

If the above step is difficult for you then you can connect these two. Both the pins are 3.3V so they won't make any difference.

For me the first option was easier so after mofification my module looks like this.

Connection Diagram:

Now connect the pins accordingly.

• VIN to nodeMCU 3.3V Pin
• SCL to nodeMCU D1 Pin
• SDA to nodeMCU D2 Pin
• INT to nodeMCU D0 Pin
• GND to nodeMCU GND Pin

Before you upload the code library needs to be installed. Please follow the below mention instruction to install the library.
https://creativestudio1973.blogspot.com/2019/11/introduction-to-arduino-library-manager.html

Source Code:

Video:

Datasheet:

https://datasheets.maximintegrated.com/en/ds/MAX30100.pdf

Reference:
[1] Sarkar, S., Ghosh, A., Chakraborty, M., & Mondal, A. (2024). Design, Hardware Implementation of a Domestic Pulse Oximeter Using IOT for COVID – 19 Patient. International Journal of Microsystems and Iot, 2(1), 469–475. https://doi.org/10.5281/zenodo.10629635

Light Sensor BH1750 Interface with Arduino

Light Intensity is an important parameter. This could be measured by various components (eg. LDR) with proper calibration. This is why BH1750 is easy to use. It has an I2C interface so data could be extracted easily using the I2C Bus.

Things we need:

• BH1750
• Arduino
• Jumper Wires
• Bread Board (Optional)

Connection Diagram:

Connection is very simple, BH1750 has five pins Vcc, Gnd, SCL, SDA, Addr. Connect the pins accordingly.

• VCC pin to Arduino 5V
• GND pin to Arduino Ground
• SCL pin to Arduino A5
• SDA pin to Arduino A4

Once the connection is done open Arduino IDE and upload the code below.

Before you upload the code library needs to be installed. Please follow the below mention instruction to install the library.
https://creativestudio1973.blogspot.com/2019/11/introduction-to-arduino-library-manager.html

Source Code:

Video:

Dot Matrix Display Interface with Arduino using MAX7219 Driver

In our previous blog, we discussed interfacing of Dot Matrix Display with Arduino and found out that the process consumes lots of Arduino pins. To solve this issue we will use a driver IC. With help of this driver IC, we will control an 8x8 Dot Matrix Display using only 3 I/O pins. 

The module has five pins. Their descriptions are given below.

VCC  - 5V
GND  - Ground
DIN    - Data In

CS      - Chip Select
CLK   - Clock

Materials Required:

• Dot Matrix Display Module
• Jumper Wires
• Arduino

Circuit Diagram:

• VCC pin to Arduino 5V pin
• GND pin to Arduino GND pin 
• DIN pin to Arduino Pin 11
• CS pin to Arduino Pin 7
• CLK pin to Arduino Pin 13

Connect the display module with Arduino as shown above. After the connection is complete then upload the program. You should find the result as shown in the below video.

Source Code:

In this second version, the array is introduced. Using array we can store multiple values in a variable. This allows us to make the code short. If you go through the resulting video you will find that this second version is more complex sill the code size is less. 

Source Code 2:

Video: 

Video 2:

Dot Matrix Display Interface with Arduino

Dot Matrix displays are categorized upon their number of rows and number of columns and size of pixels. Usually, dot matrix displays come in the square shape of 8x8 LEDs but here we are going to demonstrate a 7x5 LEDs Display. The benefit of a dot matrix display is that you will be able to display characters or images using this. The process shown here is very simple to understand but the drawback is that this process consumes lots of pins. If you look at the Arduino in the video below you will see that 12 digital I/O pins are used to control one display. For come controllers, we might not have 12 I/O pins at all. The process of overcoming this scenario we will discuss in our next blog.

Things we need:

• Arduino
• 7x5 Dot Matrix Display
• 330 Ohms - 7 Nos
• Dot Vero (KS-100) or Bread Board
• Jumper Wires
• Soldering Kit (Not required for Bread Board)

Connection Diagram:

Connect the pins as described then upload the code below. The first code is about displaying a heart in portrait mode and the second code is about displaying the same heart in landscape mode. Check the results in the video below.

Source Code:

Video:

7 Segment Display Interface With Arduino

Seven segment displays come in different sizes. Their pin configuration also varies. So after purchasing any Common Cathode (CC) or Common Anode (CA) type display one must find the pin configuration. Usually, the datasheet could be found using the printed model number on the 7-Segment display. Depending upon the type (CC or CA) drivers are available to drive a display. Otherwise, they require an 8bit data line and 1bit control line per display. Drivers also help to drive the current for segments as sometimes for bigger displays the requirement of the current might be more than the controller could supply.

In a 7 Segment Display, the segments are named as a,b,c,...,e,f, and Dot Point. The segments are positioned as below.

   

To interface 7-Seg display with Arduino, we need

• Arduino UNO / NANO
• 7-Seg Display Common Anode type
• 330 Ohms Resistor
• 40x1 Male Berg Strip
• Dot Vero or Bread Board
• Connecting Wires
• Jumper Wires - Male Female Type
• Soldering Kit (Not required for Bread Board)

Connection Diagram:

• D2 is connected to A
• D3 is connected to B
• D4 is connected to C
• D5 is connected to D
• D6 is connected to E
• D7 is connected to F
• D8 is connected to G
• D9 is connected to Common Pin

Once the connection is complete copy the below code to Arduino IDE and upload it to your Arduino.

The code is for displaying 0-9. After uploading you should see the counting started. Please check the video for results.

Troubleshoot:

• If you find that all the segments are not glowing at 8 that means there are some wires that are not connected properly.
• If you see that display is showing abnormal values please check the connection diagram between Arduino and the Display.

Source Code:

Video:

 

Introduction to LED Based Displays

LEDs are the most basic kind of display. But the problem is One LED has only two states, On state and Off state. So it can not give more than two outputs. If we need more than two outputs what option do we have?

We can use multiple LEDs to make a display. So eight LEDs are combined together to make a display that can show 0-9 and Dot point. To display a digit maximum of seven segments consists of seven LEDs are used. Hence the name came Seven Segment Display. Eight LEDs can be connected in two ways either we could common all of their positive together or the negative together. This is why we have two types of seven-segment displays. Common cathode and common anode. A typical structure and connection diagram of the 7-Segment display is shown below. 0-9 is not enough to display right? What if we need to display characters, symbols, or images?

       

Dot Matrix displays are the solutions. Multiple LEDs are connected together to form an array. They are connected row-wise cathode and column-wise anode or vice-versa. Now with this formation, we can easily display anything we want. If we use RGB LEDs then displaying colored images also possible.  A typical connection diagram and image of the dot matrix display are shown below.